陽極氧化鋁油墨  【一、使用技術說明】 1.產品特性：平光、免固化劑、免洪烤、快干、耐沖壓、可絲印及移??； 2.環保性:符合歐洲重金屬EN-71-3、 美國ASTM-963、歐盟ROHS、鄰苯二甲酸鹽6P等標準； 3.適用范圍:各種金屬、合金、玻璃、陶瓷、電鍍、石材、陽極氧化鋁表面及烤 （噴）漆面等； 4.稀釋劑: 用本公司783稀釋劑。洗網用718洗網水； 5.網紗與用量: 適合77T-140T（180目-350目）網紗，用300目網版每公斤約可印30平方米； 6.固化劑: 可以提高油墨油附著力及性能。本油墨單組份使用,不用添加.如有特殊要求可以加本公司TA-9固化劑,添加量10%； 7.干燥方法：自然揮發干燥，墨層表干時間5-10分鐘：實干時間24小時以內，也可以80度烤15分鐘。 干燥溫度25℃60℃80℃100℃干燥時間24小時40分鐘20分鐘15分鐘 【二、性能測試方法】 檢驗項目測試條件檢驗結果附著力百格劃百格后用3M膠紙剝離較少3次以上100%無脫落耐酒精測試用浸有純度99%的酒精的棉球，500G力在油墨表面來回擦拭100次無變化耐沖壓測試1MM鋁片折彎180度無變化   【三、使用注意事項】  1、試印確認符合要求后再批量生產。 2、做好被印物的表面清除油脂及雜質工作，以促進附著效果。 3、需要套色時，應在前顏色表干或硬干后再進行套色工作。 4、附著力、硬度、耐酸性、耐油性、耐去漬油性、抗劃傷性、耐磨性等性能的檢測，需要墨層   完全固化后方可檢測。 5、未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。 6、添加固化劑后的使用時限：加入固化劑后的油墨使用時間為4-6小時，環境溫度越高使用時間越短，剩余油墨不可回收。 7、油墨，稀釋劑使用及儲存時嚴禁煙火。 8、使用時注意施工場所的通風狀況良好。[technical instructions]1. product characteristics: Pingguang, free curing agent, baking, drying, non flood resistant stamping, screen printing and printing;2. environmental protection: in line with the European heavy metals EN-71-3, the United States ASTM-963, the European Union ROHS, phthalate two, formic acid, 6P and other standards;3. scope of application: all kinds of metals, alloys, glass, ceramics, electroplating, stone, anodized aluminum surface and baking (spraying) paint, etc.;4. thinner: use our company's 783 thinner. Wash the net with 718 net water;5. mesh and dosage: for 77T-140T (180 -350 mesh) mesh, 300 mesh screen can be printed per kilogram of about 30 square meters;6. curing agent: can improve ink oil adhesion and performance. The ink component use, do not add. If there are special requirements can be added to this TA-9 curing agent, adding amount of 10%;7. drying method: natural evaporation drying, ink table drying time of 5-10 minutes: solid time less than 24 hours, you can also bake 80 degrees 15 minutes.drying temperature25 C60 C80 C100 Cdrying time24 hours40 minutes20 minutes15 minutes[two] methods of performance test]Inspection itemTest conditionTest resultAdhesion scaleAfter scaling, peel off at least 3 times with 3M tape100% without peeling offAlcohol tolerance testWith a cotton ball impregnated with 99% alcohol, the 500G force is wiped back and forth 100 times on the surface of the inkunchangedStamping test1MM aluminum sheet bending 180 degreesunchanged[three, the use of attention]1, test printing confirmed compliance with the requirements, and then mass production.2, do a good job of printing the surface of the oil and impurities to remove the work to promote the adhesion effect.3, need to register, should be before the color table dry or hard after the registration work.4, adhesion, hardness, acid resistance, oil resistance, resistance to oil stains, scratch resistance, abrasion resistance and other properties of the test, you need ink layerFully solidified before inspection.5, without permission, shall not use this series of ink mixed with other types of ink and color matching.6, add curing agent after the use of time limit: the use of curing agent after the use of ink for 4-6 hours, the higher the ambient temperature, the shorter the use time, the remaining ink can not be recycled.7, ink, diluent use and storage is strictly prohibited fireworks.8, the use of attention to the construction site ventilation in good condition.